Categories
| Price: | US $ 30000-110000/Set |
|---|---|
| Min Order: | 1/Set |
| Pay Type: | L/C,T/T |
Tire recycling machine with auxillary equipment:
1. Tire ring cutting machine
Tire ring cutting machine is an alone accessory machine, it puts the tire which is greater than 650 type (both nylon and steel wire) flat on the machine, locking tire inside opening through up and down locking system, then putting alloy tools to target to the place of disintegration of tire to cut off the mouth and nation of tire, finished in 3 minutes. The power is 4kw; revolting speech is 40r/min, Shape dimension: 1.8m*1.3m*1.6m.
2. Tire strip cutting machine
Tire strip cutting machine make use of two round special cutting tools to combination running cutting. It can cut the tire of circle cutting into 3-8mm wide strip, to use for dicer cutting. The material of this machine's knife disk is special alloy structural steel (scientific name: Nine-chrome-silicon), diameter of knife disk isΦ390mm, hardness is 58-62GrS, more durable. With the hand grinding wheel cast when not sharp, power is 4kw, revolting speech is 45r/min, shape dimension: 1.3m*0.8m*1.65m.
3. Tire block cutting machine
Tire block cutting machine is prepared for the crush of host machine, Not only it makes the cutting strip-type waste rubber cut into about 3*8cm small pieces, but also can enter into host machine again through mutual use between sword and fixed knife, convenient to feed, high output and won't damage roller easily, power is 5.5kw, revolting speech is 380r/min,shape dimension: 1m*0.8m*1.4m. To pay attention to the space between sword knife and fixed knife when the machine is in operation, best to keep at around 0.1mm, so that the steel wire can be cut off.
4. Steel wire separator
The main working part of this machine is two relative rotary roll shafts with the same speed. When tire circle cut into the middle of two rollers, it will be extruded by roll shaft, at the same time, be squeezed, Sheared and tear by the two relative rotary rollers. And finally complete the separation of the steel wheel by many times.
Main Specification | |||||
Model No. | XKP-350 | XKP-400 | XKP-450 | XKP-560 | XKP-560L |
Diameter of front roll | 300 mm (groove) | 400 mm (groove) | 450 mm (groove) | 560 mm (groove) | 560 mm (groove) |
Diameter of back roll | 300 mm (groove) | 400 mm (groove) | 450 mm (groove) | 510 mm (groove) | 560 mm (groove) |
Drum working length | 500mm | 600mm | 760mm | 800mm | 1000mm |
Front roll liner speed | 26.2m/min | 34.5 m/min | 38.0 m/min | 40.6m/min | 44m/min |
Roll ratio | 1:2.5 | 1:2.5 | 1:2.5 | 1:2.5 | 1:2.5 |
Max roller spacing | 10mm | 10 mm | 10 mm | 10 mm | 10mm |
Motor power | 30KW/37KW | 45KW/55KW | 55KW /75KW | 75KW/90KW | 110 KW/132KW |
Weight | 6T | 8.5 T | 11T | 17.5T | 21T |
L*W*H | 3.5*1.6*1.5m | 4.3*1.8*1.6m | 4.6*2.0*1.65m | 5.3*2.0*1.7m | 5.6*2.0*1.7m |
* Inquiry and consulting support.
* View our Factory.
* Training how to instal the machine, training how to use the machine.
* Engineers available to service machinery overseas.
| Prod Model: | XKP350/XKP400/XKP450/XKP560/XKP560L |
|---|---|
| Type: | Tire Machine |
| Power(W: | 30-132 Kw |
| Weight: | 15-23tons |
| Roll Ratio: | 1:2.5 |
| Front Roll Liner Speed: | 34.5-44 M/Min |
| Diameter Of Roll: | 400-560mm |
| Max Roller Spacing: | 10 mm |
| Motor Revolution Speed: | 760-980 R/Min |
| Raw Material: | Waste Tires |
| Function: | Make Waste Tires Into Rubber Powder |
